Nothing is more frustrating than a non-functioning cooling system on a hot afternoon. The thermostat is often the issue when a cooling system fails to start or function properly. Your Braeburn thermostat not cooling may result from defects or incorrect settings. Luckily, you don’t have to call a serviceman to troubleshoot many thermostat issues.
This article will take you through the whole troubleshooting process. There are various ways of solving the issue of Braeburn thermostat not cooling. Read on to find out why the thermostat is not cooling and what you can do before calling a serviceman.
Your Braeburn thermostat may stop cooling for various reasons, including:
The first thing you should do when you notice your Braeburn thermostat is not cooling is to check if it is set in the ‘cool’ mode. If it is set on the ‘heat’ mode, it will not turn on the cooling system. If it is on the ‘cool’ mode but still won’t turn the cooling system on, you should check its set point, which is the temperature at which it turns on the cooling system.
The cooling system will not turn on if the set point is too high. The temperature in your space would have to rise to the set point before the AC starts blowing cold air. The set point should be a minimum of 3 degrees lower than the indoor temperature.
If the thermostat does not work even after adjusting the set point, then it is likely that the compressor protection feature is on. Most Braeburn thermostats have the protection feature to prevent possible cooling system damage caused by short cycling. The thermostat should work five minutes after the compressor short cycle protection elapses.
Your thermostat may not turn on the cooling system if its wiring is faulty. Check if there are any loose wires or faults in the wiring. Find the wiring terminal block on the thermostat by removing the cover, then ensure the heating and cooling stages are connected to the right terminals. Reconnect all the loose wires to the correct terminal. Refer to the user’s manual for directions on how to fix the wiring issues. Set the thermostat in the cool mode to see if it is working. If not, try the next step.
Your Braeburn thermostat may not be cooling because you installed it in the wrong place. For instance, if you install the thermostat near a window or an outside that you often leave open, it will receive an incorrect reading of your home’s temperature. In such circumstances, the thermostat misinterprets that your home does not need cooling. The same applies to installation in rooms prone to high-temperature fluctuations, like the kitchen and laundry.
If incorrect temperature readings is the issue, you can easily uninstall and reinstall the thermostat in a different location. You can use the HVAC slide drive tool to install the thermostat. It is great for HVAC applications like installations and control work.
Your thermostat could not be cooling because its batteries are low. If the unit uses batteries and it’s been over a year since you last changed them, a new set of batteries could be all you need. Get the right batteries for the unit, and remember you cannot mix old with new.
Debris trapped in an AC filter Trusted Source How to Clean an AC Filter | HGTV Wondering how to clean your air conditioning unit’s filter? HGTV outlines the types of filters you may have and shows you how to clean reusable filters to improve the air quality in your home. www.hgtv.com can cause inefficient cooling. Check the unit’s filters and see if they need to be replaced. If the filters are dusty or greyish brown, you will need to replace them asap. Check the user’s manual for the correct filters to buy and replace.
Without power, your thermostat cannot function. You may think your thermostat is receiving power when you see the LED blink. The problem is the LEDs and programming units of the Braeburn thermostat use battery power and may be active even when the unit is not getting any power. A tripped circuit breaker is one of the top reasons why a Braeburn thermostat may not receive power. According to an article by Forbes Trusted Source 4 Reasons Your AC Is Not Working Accordingly when heat waves occur, HVAC technicians have their hands full trying to keep everyone supplied with cool air. If your HVAC system quits, you may need professional help, but there are some common issues you can handle on your own. Here are 10 reasons your AC might not be working. www.forbes.com , a tripped breaker and blow fuse in the AC circuit are pretty common, especially during hot summer weather. To fix it, press it down completely then press it up until it clicks into position.
A reliable way of checking if your thermostat is receiving power is by turning the unit off, removing the cover and mounting plate, then disconnecting and reconnecting the red and green wires. You will know the thermostat is receiving power if you return the thermostat to the holder and the fan runs when you turn the power on.
If the AC motor is not charged, it won’t turn on. The thermostat cannot turn on the cooling if the AC motor is off. The AC can fail to turn on if the capacitor that charges it is faulty. Loose condenser wires can also prevent an AC from turning on. You should get help from a HVAC technician to check it the capacitor for your AC motor is faulty and if the condenser unit’s wires are still intact.
If you have tried all the troubleshooting options above and your thermostat still won’t turn the cooling system on, you can try these tips:
If none of the troubleshooting options above don’t work, you can reset the thermostat. Resetting will restore the thermostat’s settings to default, and fix all the bugs that are obstructing the cooling system. Resetting the Braeburn thermostat is such a breeze. All you have to do is find the reset button on its front then press it with a pin or paper clip. If the thermostat won’t turn the cooling system on even after resetting, then the problem could be the AC and not the thermostat.
Turn off the AC and power supply then go to the fuse box outside of your home and pull out all of the fuses. Run a continuity test on them with a multimeter and replace any that is not working.
If you end up needing a new thermostat and have no idea what to go with from the sea of options, consider the Braeburn 2020NC. It is easy to operate, thanks to its 5-2 programming and adaptive recovery mode.
Your Braeburn thermostat may fail to turn on the cooling system for various reasons. Most times, you wouldn’t need the help of a technician to fix cooling issues. We have provided all the troubleshooting tips that can get the thermostat running again. If you are unable to solve the issue of Braeburn thermostat not cooling with the troubleshooting tips, you should probably troubleshoot your AC.
If you are unsure about troubleshooting the AC, you can get help from a HVAC expert. Some issues with the AC might be complex and you may not be able to figure it out on your own. You can also reach out to the Braeburn customer support if you feel stuck.
